#Ip virtual reassembly install#
Webvpn install svc flash:/webvpn/svc.pkg sequence 1 Ip nat inside source list 1 interface GigabitEthernet0/1 overload
Service-policy type inspect self-to-out-policy Zone-pair security self-out source self destination outside Service-policy type inspect out-to-self-policy
Zone-pair security out-self source outside destination self Service-policy type inspect firewall-policy Zone-pair security in-out source inside destination outside Policy-map type inspect self-to-out-policy Policy-map type inspect out-to-self-policy Subject-name cn=IOS-Self-Signed-Certificate-2692466680Ĭrypto pki certificate chain TP-self-signed-2692466680Ĭlass-map type inspect match-all router-access ! Last configuration change at 16:25:30 UTC Thu by ciscoĬrypto pki trustpoint TP-self-signed-2692466680 Note: A self zone is also defined to only allow http/https traffic to the router itself for access restriction. The An圜onnect traffic goes into the same security zone that the inside LAN interface belongs to post decryption. VPN traffic belongs to the same security zone as the inside network. There are two typical scenarios with An圜onnect and ZBF, and here are the final router configurations for each scenario. The resulting final configuration are included for two typical deployment scenarios later in this document.Ĭonfigure a Virtual Template interface and assign it in a security zone for traffic decrypted from the An圜onnect connection.Īdd the previously configured Virtual Template to the WebVPN context for the An圜onnect configuration.Ĭomplete the rest of the WebVPN and Zone Based Policy Firewall configuration. Here are the high level configuration steps that need to be performed on the Cisco IOS An圜onnect server in order to make it interoperate with the Zone Based Policy Firewall. Note: Use the Command Lookup Tool ( registered customers only) to obtain more information on the commands used in this section. In this section, you are presented with the information to configure the features described in this document. Refer to the Cisco Technical Tips Conventions for more information on document conventions. If your network is live, make sure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment.
#Ip virtual reassembly software#
The information in this document is based on these software and hardware versions:Ĭisco IOS 3845 series router running version 15.0(1)M1 Advanced Security feature setĬisco An圜onnect SSL VPN Client version for Windows In order to take advantage of the new capability in Cisco IOS, you need to ensure the Cisco IOS WebVPN gateway device is running Cisco IOS Software Release 12.4(20)T3, Cisco IOS Software Release12.4(22)T2, or Cisco IOS Software Release12.4(24)T1 and later. With the new code, the user can assign a security zone to a virtual-template interface, which is referenced under the WebVPN context, in order to associate a security zone with the WebVPN context. This issue was later addressed in newer software releases of Cisco IOS.
Of the interfaces not being cfged for zoning The symptom of this problem can be seen with this log message reported by the firewall: *Mar 4 16:43:18.251: %FW-6-DROP_PKT: Dropping icmp Since the user cannot configure the SSLVPN-VIF0 interface to make it a zone member, VPN client traffic terminated on the Cisco IOS WebVPN gateway after decryption cannot be forwarded to any other interface belonging to a security zone. This created a problem with An圜onnect VPN and Zone Based Policy Firewall since with the firewall, traffic can only flow between two interfaces when both interfaces belong to security zones. But, this SSLVPN-VIF0 interface is an internal interface, which does not support user configurations. In Cisco IOS ® Software Release 12.4(20)T and later, a virtual interface SSLVPN-VIF0 was introduced for An圜onnect VPN client connections.
0 kommentar(er)
